Lost Mary BM6000 Not Working? – Troubleshooting & Fix Guide

Why Is My Lost Mary BM6000 Not Working: Common Issues & How To Fix Them

Below are some common issues with Lost Mary BM6000 and some troubleshooting tips to help you get your device up and running. 

Device is Not Producing Vapour:

Causes:

If you notice your device is not producing vapour or is producing low vapour, it could be due to a few reasons. Your device battery is empty, or the coil inside the pod may be burnt. 

How To Fix It?

Connect your device to a power source and fully charge it. If it doesn't work after charging, the device may be faulty. If the burnt coil inside your pod is the reason behind low vapour production, replace the pod.

Device is Not Hitting

Causes:

If your Lost Mary BM6000 is not hitting, it could be due to a few possible reasons, like blocked airflow, a damaged coil inside the pod, or e-liquid inside the pod has run out. 

How To Fix It?

If your Lost Mary BM6000 is not hitting, first check that the pod is fully inserted and securely connected to the device. Make sure the battery is sufficiently charged, as a low battery can prevent the device from working properly. If the problem persists, try using a different pod to determine whether the pod is defective. 

Looking to buy Lost Mary vapes? Explore the full Lost Mary range to find your preferred device for your vaping needs. 

Leakage:

Causes:

Lost Mary BM6000 leakage is due to improper pod installation, exposure to high temperature and damaged pod during shipping. 

How To Fix It?

To reduce the risk of leaking, try not to draw puffs overly hard or fast, as this can affect how the e-liquid flows through the pod. It's also best to store your Lost Mary BM6000 upright and keep it away from extreme temperatures, which can affect the consistency of the e-liquid and increase the risk of leaking. 

Blinking while charging:

Causes:

Wondering why my Lost Mary BM6000 is blinking while charging? This is because you dropped it in water, which most likely means it's likely that water has got inside the device and caused a short circuit. Another common reason is a low battery, which can also cause the device to blink while charging. This issue can also occur if your device has been dropped on a hard surface, causing the battery to disconnect and stop charging.

How To Fix It?

If your device is blinking while charging due to a low battery, charge your device. However, if the problem is due to the disconnected battery, open the device, and you may notice that a red wire is disconnected from a solder point. Reconnecting it with a small piece of electrical tape may allow your Lost Mary to charge again. 

Blocked Airflow

Causes:

Airflow is essential for draw activation. If you experience blocked airflow, it usually happens when dust blocks the airflow holes and the e-liquid gets too thick. This stops air from hitting the internal airflow sensor, resulting in blocked airflow. New devices come with protective seals, which can block airflow.

How To Fix It?

Check the mouthpiece for any debris, dust, or e-liquid buildup that may be blocking the airflow. Also, remove any protective seals from the device and make sure you don't cover the airflow holes while vaping. 

Burnt Taste

Causes:

The Lost Mary BM6000 burnt taste is due to various reasons. The e-liquid inside the device has run low or been completely used up, causing the coil to burn dry. Taking long or frequent puffs can overheat the coil, resulting in a burnt or harsh taste.

How To Fix It?

Put your device down for a moment when you notice a burnt taste to give the wick time to absorb more vape liquid. If the burnt taste continues, the e-liquid has likely run out, and the pod will need to be replaced. Try taking slower, longer puffs and waiting 15 to 20 seconds between each draw to prevent the coil from overheating.

FAQs

Why Is My Lost Mary BM6000 Not Hitting?

The most common causes include blocked airflow,  low battery, and empty e-liquid. 

How Can I Extend The Battery Life Of My Lost Mary BM6000?

To help extend the battery life of your Lost Mary BM6000, always use a 1A USB-C charging adapter, as higher-powered chargers can cause overheating. Allow the device to charge fully until the LED indicator stops blinking, which usually takes around 45 to 60 minutes. It is also recommended to avoid vaping while the device is charging, as this can put additional strain on the battery and internal circuitry.

How Do I Know When To  Switch Pod Of Lost Mary BM6000?

You should switch the pod of your Lost Mary BM6000 when you notice a burnt taste, a significant drop in flavour quality, reduced vapour production, or the pod runs out of e-liquid. 

How Can I Prevent Future Issues With My Lost Mary BM6000?

To help prevent future issues with your Lost Mary BM6000, store the device upright whenever possible to reduce the risk of leaking. Avoid exposing it to extreme temperatures, as this can affect both battery performance and e-liquid quality. Also, recharge the battery regularly and avoid leaving it completely drained for long periods, as this can reduce its overall performance and lifespan. 

Where Can I Buy Lost Mary BM6000 Pods And A Pod Kit?

If you're looking to buy Lost Mary BM6000 pods and pod kits in the UK, you can find a wide selection of Lost Mary products at Vape Gala. We stock a range of Lost Mary BM6000 pod kits and replacement pods in popular flavours, all sourced from trusted suppliers. Buying from one of the best online vape shops in the UK not only ensures you're getting quality products but also gives you more flavour choices, better prices, and a smoother shopping experience. Shop now!